Propane runtime estimate
Estimate fuel-energy days from available propane mass and appliance input ratings.
Use actual labels, manuals, and measurements. This worksheet does not certify equipment safety.
Collect the measurements first.
Blank fields have no assumed value. Enter zero for unused loads. The worked example below explains every input.
Estimate consumption from fuel input
This worksheet estimates how many days of the entered appliance use can be supplied by a stated mass of propane. It is not a check of the tank, regulator, piping, or appliance installation. It cannot predict whether a container can vaporize fuel fast enough in cold conditions or whether a system can supply several appliances simultaneously. A long estimated runtime does not establish adequate delivery capacity.
Enter the propane fuel mass available, excluding the weight of the cylinder or tank. A container’s label or marketing size is not a measurement of how much fuel remains today. Use a reliable fuel-quantity record or an appropriate measurement interpreted by someone qualified to do so. The page deliberately provides no filling, draining, valve, regulator, or repair instructions.
The energy constant and its limits
The calculation uses 21,548 BTU per pound of propane. This value comes from the physical-properties table in the Propane Education & Research Council’s 2011 training publication, hosted by the U.S. Department of Energy: Converting Vehicles to Propane Autogas, Part 1, PDF page 22, printed page 12. The table labels it total heating value after vaporization. It is used here only as an energy-accounting constant, not as an RV installation specification.
The tool multiplies available fuel mass minus your chosen reserve by that constant. It then divides the energy by daily fuel-input demand. Appliance ratings must use a compatible fuel-input heating-value basis. If the documentation gives heat delivered to the living space instead of fuel energy consumed, do not substitute that output rating. Obtain the correct input figure from the appliance manufacturer.
Count burner-on time, not just switched-on time
For each of the three appliance rows, enter the rated input in BTU per hour and the number of hours per day the burner is actually operating at that input. Daily demand is the sum of each rate multiplied by its operating hours. A furnace enabled overnight may cycle on and off; entering the entire night at full input describes continuous operation, not necessarily the thermostat-controlled case.
A refrigerator or water heater may also cycle or use a different energy source. Record which operating mode the estimate covers. If an appliance modulates its input, use a documented equivalent average or evaluate separate scenarios. Do not halve a rated input and halve the hours for the same duty cycle, because that would count the reduction twice.
A transparent worked example
Assume 20 lb of available propane and a chosen 2 lb reserve. The amount included in the estimate is 18 lb. Multiplying 18 by 21,548 gives 387,864 BTU. Assume one appliance with an illustrative input of 20,000 BTU per hour operating for four burner-on hours per day. The daily demand is 80,000 BTU.
Divide 387,864 by 80,000 to obtain approximately 4.85 days. Daily fuel consumption is approximately 3.71 lb. Enter zero input and zero hours for the two unused appliance rows. These values illustrate the formula; they are not a statement that a particular furnace will run four hours or that a nominal cylinder contains exactly 20 lb at departure.
If the same appliance instead burns for eight hours per day, demand doubles to 160,000 BTU and the energy estimate falls to about 2.42 days. That change models additional consumption only. It does not model a temperature forecast, insulation performance, wind, or fuel vaporization. Keep those distinctions visible when comparing scenarios.
Add each consumer that shares the fuel
Include other appliances drawing from the same supply. A stove, furnace, refrigerator, and water heater should not each be assigned the entire container in separate estimates and then treated as if all those runtimes can happen together. When more than three appliances need representation, combine their daily input energy carefully into an equivalent row and retain the underlying calculation.
A reserve is a planning choice, not a guaranteed usable quantity at the appliance. The worksheet lets you exclude some fuel but does not declare a minimum reserve suitable for any weather or trip. Zero available fuel produces zero runtime when daily demand is positive. A zero-demand entry is rejected rather than displaying an unhelpful infinite runtime.
Stop at the boundary of the arithmetic
The Jayco towable manual treats propane systems and their equipment instructions separately from ordinary trip planning. Follow the documentation for your own RV and appliances. A fuel estimate cannot diagnose a smell, malfunction, flame issue, or suspected leak. Those situations require the relevant emergency instructions and qualified assistance, not experimentation with calculator inputs.
Keep an estimate with its assumptions and update it when fuel quantity or appliance use changes. The propane runtime guide explains how to organize the consumption worksheet. Use the applicable appliance instructions and ask a qualified professional about equipment compatibility or performance.